AI Detection and Printing Errors

When AnkerMake Studio processes the slicing of a model, it generates images of simulated perspectives at different heights. When the AI is enabled, every time the M5 prints a layer, the camera takes a picture and compares it with the images of simulated perspectives locally. After the first layer is printed, the Z-axis raises 50 mm to help the camera perform a clearer comparison. If the AI detects print abnormalities, you will see the following error message:

Solution:

• Observe the printing status of the workpiece model. If there is indeed a printing error, stop printing. If there is no printing error, ignore the warning and continue printing.

Common Issues and Solutions:

1. Looks Like Spaghetti
   1. Cause: The print isn't sticking to the hotbed, causing the model to leave the position of the platform plate during printing.

 

Solution:

1. Increase Brim and Use Raft:
   1. Go to AnkerMake Studio, increase the brim, and use a raft to increase the adhesion area by navigating to Expert Mode > Build Plate Adhesion > Build Plate Adhesion Type > Brim.

 

Adjust Print Temperature:

• Ensure the print temperature follows the recommended range for the filament. Increase the hotbed temperature if necessary:
  • PLA+: Do not exceed 65°C
  • ABS/PETG: Do not exceed 100°C

Ensure Filament Feeding:

• Position the filament spool to minimize resistance during feeding.
• If the filament is stuck for a short time during printing and then resumes extruding, it can cause defects. Position the filament spool to minimize resistance when feeding.
• Position the filament spool so that it will unwind counterclockwise.

 

Layer Shifting in the Y-Axis

 

 

Cause: Abnormal materials in the Y slot, tension issues, or improper settings.

 

Solution:

1. Remove Obstructions:
   1. Check for any foreign objects blocking the Y slot.
2. Adjust Belt Tension:
   1. Check and adjust the tension of the X and Y-axis belts. For detailed instructions, refer to X and Y Axis Belt Adjustment

Check Jerk Settings:

• In AnkerMake Studio Expert Mode, set Print Jerk to 15 mm/s for optimal print quality: Expert Mode > Speed > Enable Jerk Control.

 

Nothing is Printing When the Filament Extrudes

• Cause: Clogged nozzle or filament feeding issues.

Check Filament Spool:

• Ensure the spool is not tangled. Pause the print, unload the filament, untangle the spool, or use a new spool.

Check and Clean the Nozzle:

• Manual Feeding:
  • Preheat to 220°C and manually feed the filament to check extrusion.

 

• Cleaning the Nozzle:
  • Follow the steps in How to Clear Nozzle Blockages.
  • Remove the filament, preheat to 180°C, and use a needle to clear the blockage.
• Replace Nozzle or Hotend:
  • Refer to:
    • How to Exchange the Nozzles
    • Replacing the Hotend

Check Extruder Gear:

• Disassemble the extruder to ensure the gear moves correctly.

 

 

Check Throat Fan:

• Ensure there is air from the air outlet. Replug or replace the throat fan if necessary.

 

Clogged Nozzle/Filament leakage

 

Root Causes:

1. Nozzle contamination.
2. Model separation from the heating bed.
3. Improper nozzle assembly.

Solution:

1. Automatic Nozzle Cleaning:
   1. Select the Nozzle Clog Clean option from the maintenance interface.

Enter the automatic clog cleaning function and click start; the process takes about 10 minutes.

If the clog is still not solved, please follow method 2 to clean the plugging manually.

2. Manual Cleaning:

• Raise the extruder, remove the top and nozzle covers, preheat to 220°C, and clean the nozzle with tweezers or needle-nose pliers.

 

Additional Tips:

• Pay close attention to the heated nozzle due to its high temperature to prevent burning yourself.
• If difficult to clean, preheat the nozzle to 240°C. If you are printing high-temperature filaments such as ABS and TPU, increase the preheating temperature accordingly.
• Clean slowly and gently to avoid breaking the thermistor wire.
• Remove the air guide first, and use a heat gun to remove the connection part with the heating wire and the thermistor wire if difficult to remove.

 

1. After cleaning, preheat the nozzle to 200°C and tighten the nozzle with a socket wrench.

 

If the thermistor wire breaks during cleaning, replace the hot end:

Article： How-to-Replace-the-Hotend-of-M5

Video： How-to-Replace-the-Hotend-of-M5

 

Camera Blocked

• Cause: AI cannot perform normally due to the camera being blocked by foreign objects.

Solution:

• Remove objects blocking the camera.

 

If you have encountered different print quality issues, contact AnkerMake Customer Support at us for assistance.